Slip Free Rolls

$242.53 - $349.91
SKU:
WUS000069
Selected Color is
Black
Yellow
Black/Yellow
Adding to cart… The item has been added
An anti-slip tread roll provides an instant non-slip, self-adhesive surface perfect for paths, ramps, loading bays and entranceways. Features and Benefits of Slip-Free Tread Roll: Helps prevent slips and falls in light or medium traffic areas Use on…

Product Detail

An anti-slip tread roll provides an instant non-slip, self-adhesive surface perfect for paths, ramps, loading bays and entranceways.

Features and Benefits of Slip-Free Tread Roll:

  • Helps prevent slips and falls in light or medium traffic areas
  • Use on interior and exterior surfaces
  • Suitable for concrete, wood, brick, stone and metal
  • Made of a tough aluminium oxide grit resin-bonded to thick PVC
  • Pressure sensitive adhesive backing
  • Safety Tape Primer will help adhesion to dusty or porous surfaces
  • For very heavy traffic areas we recommend using Safety Coat Plus Floor Coating or Anti-Slip Fiberglass FRP Sheets.

Specifications

Usage Interior/Exterior: Interior or Exterior
Suitable for: Concrete, wood, brick, stone and metal floors and ramps
Primer Required: Use Safety Tape Primer on dusty, porous or gritty surfaces

How to Apply

Surface Preparation: Apply to clean, smooth, dry surfaces such as painted or varnished wood, concrete, metal, tiles, and terrazzo. Apply direct to smooth, hard concrete; dusty concrete will require a primer.

Priming: Smooth, non porous, dust free surfaces do not require priming. To improve adhesion on weak, dusty surfaces, apply a coat of Safety Tape Primer.

Application: Avoid application at temperatures below 50°F. Low temperatures can reduce adhesion. On steps and nosings, apply the product approximately 10mm in from the edge to prevent premature wear and edge curl. Peel back the backing strip approximately 50mm to reveal the adhesive layer. Avoid removing too much of the backing strip, but slowly keep peeling it back while firming the product into place. Firming down by hand or foot pressure is generally sufficient. A rubber mallet is recommended for firming Conformable Safety Tape and Conformable Slip Free Treads (the flexible, aluminium backed products) into place. Avoid stretching the tapes and treads during application.

Adhesion: Although the product can be walked on virtually straight away, the adhesive can take 24 hours to set fully. Immediately after placing the item onto the substrate, it can be peeled off reasonably easily for repositioning if necessary. Avoid lifting the tread or removing the tape to allow the adhesive to cure. Please allow the adhesive to set for up to 24 hours, especially if using in heavily trafficked or hazardous areas.

An anti-slip tread roll provides an instant non-slip, self-adhesive surface perfect for paths, ramps, loading bays and entranceways.

Features and Benefits of Slip-Free Tread Roll:

  • Helps prevent slips and falls in light or medium traffic areas
  • Use on interior and exterior surfaces
  • Suitable for concrete, wood, brick, stone and metal
  • Made of a tough aluminium oxide grit resin-bonded to thick PVC
  • Pressure sensitive adhesive backing
  • Safety Tape Primer will help adhesion to dusty or porous surfaces
  • For very heavy traffic areas we recommend using Safety Coat Plus Floor Coating or Anti-Slip Fiberglass FRP Sheets.

Usage Interior/Exterior: Interior or Exterior
Suitable for: Concrete, wood, brick, stone and metal floors and ramps
Primer Required: Use Safety Tape Primer on dusty, porous or gritty surfaces

Surface Preparation: Apply to clean, smooth, dry surfaces such as painted or varnished wood, concrete, metal, tiles, and terrazzo. Apply direct to smooth, hard concrete; dusty concrete will require a primer.

Priming: Smooth, non porous, dust free surfaces do not require priming. To improve adhesion on weak, dusty surfaces, apply a coat of Safety Tape Primer.

Application: Avoid application at temperatures below 50°F. Low temperatures can reduce adhesion. On steps and nosings, apply the product approximately 10mm in from the edge to prevent premature wear and edge curl. Peel back the backing strip approximately 50mm to reveal the adhesive layer. Avoid removing too much of the backing strip, but slowly keep peeling it back while firming the product into place. Firming down by hand or foot pressure is generally sufficient. A rubber mallet is recommended for firming Conformable Safety Tape and Conformable Slip Free Treads (the flexible, aluminium backed products) into place. Avoid stretching the tapes and treads during application.

Adhesion: Although the product can be walked on virtually straight away, the adhesive can take 24 hours to set fully. Immediately after placing the item onto the substrate, it can be peeled off reasonably easily for repositioning if necessary. Avoid lifting the tread or removing the tape to allow the adhesive to cure. Please allow the adhesive to set for up to 24 hours, especially if using in heavily trafficked or hazardous areas.