Product Detail
Anti Slip Traffic Paint contains a pre-dispersed lightweight aggregate that provides a finely textured anti-slip surface. This non-slip parking lot paint produces a more evenly textured finish than conventional anti-slip coatings where grit is sprinkled separately into wet paint.
Our Anti-Slip Traffic Paint aint can be used for highlighting outdoor walkways, outlining parking spaces and defining safe or hazardous pedestrian & vehicle areas with your own color codes. It is also ideal for tennis courts, playgrounds, etc.
Features and Benefits of Anti-Slip Traffic Paint:
- Textured surface offers slip resistance for pedestrians
- Suitable for asphalt and concrete, inside and out
- Vibrant colors in 24 hours
- Excellent resistance to UV
- Can be applied to damp surfaces
- Covers approximately 120 to 160 sq. ft. per gallon; one coat covers most surfaces
For garages and mechanic shops we would recommend an epoxy resin coating such as our Safety Coat Standard coating.
Specifications
| Appearance: | Matte, finely textured |
| Primer Required: | No |
| Properties: | Tough, slip resistant, can highlight areas, smarten up drab areas, excellent UV resistance, can be applied to damp |
| Suitable for: | Asphalt, tarmac, concrete, brick, masonry and similar porous surfaces. |
| Shelf Life: | 12 months in unopened container |
How to Apply
Surface Preparation
Watco Anti Slip Traffic Paint can be applied to asphalt, tarmac and porous concrete. Ensure the surface is clean, sound and dry (slightly damp is acceptable). Watco Anti Slip Traffic Paint can be applied to existing paint provided all poorly bonded material is removed and glossy surfaces are dulled using abrasive paper.
Application
If appearance is critical, we recommend the application of a small trial area first.
Stir contents thoroughly to blend in any settlement. Apply paint by brush or medium pile type roller. One coat is generally sufficient, although a second coat may be required on very porous or rough surfaces. Avoid applying too thickly. The fine texture may not be immediately apparent as the product is first applied. The texture develops further as the paint dries. Do not apply externally if rain or frost is forecast or if the temperature is below 50°F. The second coat can often be applied after as little as 1 hour depending upon drying conditions.
In exceptional temperature conditions advice should be obtained from Watcos Technical Department.
Data Sheet
Anti Slip Traffic Paint contains a pre-dispersed lightweight aggregate that provides a finely textured anti-slip surface. This non-slip parking lot paint produces a more evenly textured finish than conventional anti-slip coatings where grit is sprinkled separately into wet paint.
Our Anti-Slip Traffic Paint aint can be used for highlighting outdoor walkways, outlining parking spaces and defining safe or hazardous pedestrian & vehicle areas with your own color codes. It is also ideal for tennis courts, playgrounds, etc.
Features and Benefits of Anti-Slip Traffic Paint:
- Textured surface offers slip resistance for pedestrians
- Suitable for asphalt and concrete, inside and out
- Vibrant colors in 24 hours
- Excellent resistance to UV
- Can be applied to damp surfaces
- Covers approximately 120 to 160 sq. ft. per gallon; one coat covers most surfaces
For garages and mechanic shops we would recommend an epoxy resin coating such as our Safety Coat Standard coating.
| Appearance: | Matte, finely textured |
| Primer Required: | No |
| Properties: | Tough, slip resistant, can highlight areas, smarten up drab areas, excellent UV resistance, can be applied to damp |
| Suitable for: | Asphalt, tarmac, concrete, brick, masonry and similar porous surfaces. |
| Shelf Life: | 12 months in unopened container |
Surface Preparation
Watco Anti Slip Traffic Paint can be applied to asphalt, tarmac and porous concrete. Ensure the surface is clean, sound and dry (slightly damp is acceptable). Watco Anti Slip Traffic Paint can be applied to existing paint provided all poorly bonded material is removed and glossy surfaces are dulled using abrasive paper.
Application
If appearance is critical, we recommend the application of a small trial area first.
Stir contents thoroughly to blend in any settlement. Apply paint by brush or medium pile type roller. One coat is generally sufficient, although a second coat may be required on very porous or rough surfaces. Avoid applying too thickly. The fine texture may not be immediately apparent as the product is first applied. The texture develops further as the paint dries. Do not apply externally if rain or frost is forecast or if the temperature is below 50°F. The second coat can often be applied after as little as 1 hour depending upon drying conditions.
In exceptional temperature conditions advice should be obtained from Watcos Technical Department.
