Flowtop

$148.27
SKU:
A040607
Selected Color is
Gray
Tile Red
Tan
Adding to cart… The item has been added
Flowtop® has 33% greater compressive strength than most concrete surfaces and 90% greater tensile strength. Flowtop® is a pourable self-smoothing leveler to resurface damaged or rough concrete surfaces. It contains polyamide fibers which reinforce th…

Product Detail

Flowtop® has 33% greater compressive strength than most concrete surfaces and 90% greater tensile strength.

Flowtop® is a pourable self-smoothing leveler to resurface damaged or rough concrete surfaces. It contains polyamide fibers which reinforce the microstructure to make it even stronger and improve its resistance to shocks and abrasion. The finished surface is extremely durable and is suitable for forklift truck traffic and general industrial use.

  • Simple and easy to apply
  • Fiber reinforced to give a stronger, more durable surface
  • Proven to have low slip potential
  • Self-smoothing
  • High strength at only 3mm thick
  • Can apply an extra coat if required
  • Suitable for interior use
  • Covers approximately 38 sq. ft. per 55 lb. pack at 1/8" thick. Primers included
  • Can be painted or left bare as a non-dusting surface
  • Ready for foot traffic after 6 hours and forklift traffic after 24 hours
  • Ideal for warehouses, factories, parking lots, sidewalks, workshops, and auto body garages

Warning: Cancer and Reproductive harm image

Flowtop is far stronger than Concrete.
Comparison over 28 days
Tensile Strength Flowtop 1131 psi Concrete 493 psi
Flexural Strength Flowtop 1407 psi Concrete 1001 psi
Compressive Strength Flowtop 5757 psi Concrete 4322 psi

Specifications

Usage Interior/Exterior: Interior
Properties: Pourable resurfacing material, high strength surface, smooth finish, quick and easy to apply, inherently slip resistant, can be over coated, high strength even at 3mm
Suitable for: Concrete
Coverage: Approximately 38 sq. ft. per 55 lb. kit at 1/8" thick

How to Apply

Surface Preparation
The concrete surface should be reasonably clean and free of loose material. A good sweeping with a stiff broom is usually sufficient. Remove heavy oil and grease contamination using Bio-D Floor Degreaser and Cleaner or a similar degreaser. Flowtop can be applied to a damp concrete surface. The Flowtop materials should be stored for 8 hours prior to use at a temperature range of 60-75°F.

Priming
Two primers are supplied. Dampen areas of bare concrete with clean cold water and leave for 20-30 minutes. Apply Primer 1 to the prepared surface by brush and allow it to soak into the concrete for at least 15-20 minutes. Primer 1 can be left overnight to dry if time permits. Primer 2 can be applied while Primer 1 is still tacky or if Primer 1 has completely dried. Apply the primers evenly and avoid ponding on the surface. A sufficient amount of Primer 2 is supplied to allow for very absorbent surfaces, so there may be an excess amount of primer if used on a less absorbent surface. Apply only as much as is required to provide a thin, even film without ponding. If excess Primer 2 is used it can bleed through the wet Flowtop and dry on the surface. Although any dried primer will wear off as the floor is put into use, it can lead to problems if the Flowtop is going to be painted.

Mixing
Begin mixing immediately after Primer 2 has been applied. It is strongly recommended the entire kit be mixed and used rather than trying to split the kit. Empty the large container of resin into a clean empty bucket and gradually add the powder using a slow speed drill fitted with a mixing blade ensuring complete blending of the components. Continue mixing for approximately 2-3 minutes until an even color and creamy consistency is obtained. The mixed components should be used immediately. Pot Life - none. Use material as soon as it is mixed.

Application
Pour the mixed components onto the prepared surface. For best results, the Primer 2 should, at this stage, be uniformly wet over the surface. Apply more primer if required to any areas which may have dried out although ponding should be avoided. Use a rectangular trowel and squeegee to spread the mixed components across the surface of the concrete at the desired thickness. Immediately after application, use a spiked roller to release any trapped air and improve the finish. Work the spiked roller uniformly across the surface rolling each area 3 or 4 times from different directions. The spiked roller should not be used more than 20 minutes after the product has been applied (less in warm or very dry conditions). Once the Flowtop begins to cure, further use of the spike roller will start to leave roller marks which will not disappear. Care should be taken not to spread wet primer or the mixed components onto surrounding surfaces. External applications in direct sunlight can lead to hairline crazing. In exceptional temperature conditions, please contact a Watco Industrial Flooring Expert at (855) 627-6350.

Data Sheet

Flowtop® has 33% greater compressive strength than most concrete surfaces and 90% greater tensile strength.

Flowtop® is a pourable self-smoothing leveler to resurface damaged or rough concrete surfaces. It contains polyamide fibers which reinforce the microstructure to make it even stronger and improve its resistance to shocks and abrasion. The finished surface is extremely durable and is suitable for forklift truck traffic and general industrial use.

  • Simple and easy to apply
  • Fiber reinforced to give a stronger, more durable surface
  • Proven to have low slip potential
  • Self-smoothing
  • High strength at only 3mm thick
  • Can apply an extra coat if required
  • Suitable for interior use
  • Covers approximately 38 sq. ft. per 55 lb. pack at 1/8" thick. Primers included
  • Can be painted or left bare as a non-dusting surface
  • Ready for foot traffic after 6 hours and forklift traffic after 24 hours
  • Ideal for warehouses, factories, parking lots, sidewalks, workshops, and auto body garages

Warning: Cancer and Reproductive harm image

Flowtop is far stronger than Concrete.
Comparison over 28 days
Tensile Strength Flowtop 1131 psi Concrete 493 psi
Flexural Strength Flowtop 1407 psi Concrete 1001 psi
Compressive Strength Flowtop 5757 psi Concrete 4322 psi
Usage Interior/Exterior: Interior
Properties: Pourable resurfacing material, high strength surface, smooth finish, quick and easy to apply, inherently slip resistant, can be over coated, high strength even at 3mm
Suitable for: Concrete
Coverage: Approximately 38 sq. ft. per 55 lb. kit at 1/8" thick

Surface Preparation
The concrete surface should be reasonably clean and free of loose material. A good sweeping with a stiff broom is usually sufficient. Remove heavy oil and grease contamination using Bio-D Floor Degreaser and Cleaner or a similar degreaser. Flowtop can be applied to a damp concrete surface. The Flowtop materials should be stored for 8 hours prior to use at a temperature range of 60-75°F.

Priming
Two primers are supplied. Dampen areas of bare concrete with clean cold water and leave for 20-30 minutes. Apply Primer 1 to the prepared surface by brush and allow it to soak into the concrete for at least 15-20 minutes. Primer 1 can be left overnight to dry if time permits. Primer 2 can be applied while Primer 1 is still tacky or if Primer 1 has completely dried. Apply the primers evenly and avoid ponding on the surface. A sufficient amount of Primer 2 is supplied to allow for very absorbent surfaces, so there may be an excess amount of primer if used on a less absorbent surface. Apply only as much as is required to provide a thin, even film without ponding. If excess Primer 2 is used it can bleed through the wet Flowtop and dry on the surface. Although any dried primer will wear off as the floor is put into use, it can lead to problems if the Flowtop is going to be painted.

Mixing
Begin mixing immediately after Primer 2 has been applied. It is strongly recommended the entire kit be mixed and used rather than trying to split the kit. Empty the large container of resin into a clean empty bucket and gradually add the powder using a slow speed drill fitted with a mixing blade ensuring complete blending of the components. Continue mixing for approximately 2-3 minutes until an even color and creamy consistency is obtained. The mixed components should be used immediately. Pot Life - none. Use material as soon as it is mixed.

Application
Pour the mixed components onto the prepared surface. For best results, the Primer 2 should, at this stage, be uniformly wet over the surface. Apply more primer if required to any areas which may have dried out although ponding should be avoided. Use a rectangular trowel and squeegee to spread the mixed components across the surface of the concrete at the desired thickness. Immediately after application, use a spiked roller to release any trapped air and improve the finish. Work the spiked roller uniformly across the surface rolling each area 3 or 4 times from different directions. The spiked roller should not be used more than 20 minutes after the product has been applied (less in warm or very dry conditions). Once the Flowtop begins to cure, further use of the spike roller will start to leave roller marks which will not disappear. Care should be taken not to spread wet primer or the mixed components onto surrounding surfaces. External applications in direct sunlight can lead to hairline crazing. In exceptional temperature conditions, please contact a Watco Industrial Flooring Expert at (855) 627-6350.