Toughline

$91.00
SKU:
B11601156
Selected Color is
White
Yellow
Orange
Adding to cart… The item has been added
Watco Toughline incorporates the latest polyaspartic resin technology for a high quality, highly wear resistant line marking paint that can be applied as low as 15°F. This makes it the perfect line marker for unheated warehouses, walk in fridges, col…

Product Detail

Watco Toughline incorporates the latest polyaspartic resin technology for a high quality, highly wear resistant line marking paint that can be applied as low as 15°F. This makes it the perfect line marker for unheated warehouses, walk in fridges, cold stores and loading bays. It is particularly useful for exterior applications as it resists chalking, fading, weathering and UV discoloration.

  • Flexible
  • UV resistant
  • Can be applied between 15°F and 85°F
  • Takes heavy wear and tear
  • Excellent chemical resistance


Coverage: Approximately 75m of a 50mm wide line per 1 liter, allowing for one coat.

Curing times are dependent on site conditions, but the following can be used as a guide:

 

Curing Times
  70°F 40°F 32°F 14°F
   Recoatable       4-5 hrs       10-12 hrs       16 hrs       30 hrs   
   Light Traffic       6-8 hrs       18 hrs       24 hrs       36 hrs   
   Heavy Traffic       12 hrs       24 hrs       36 hrs       48 hrs   

Warning: Cancer and Reproductive harm image

Specifications

Usage Interior/Exterior: Interior or Exterior
Suitable for: Concrete, asphalt, wood and metal
Coverage: 240 linear feet at 2" wide
Recommended Number of Coats: 1
Pot Life: 25-30 minutes at 60°F
Curing Time (Hours): 6 Hours at 70°F

How to Apply

Surface Preparation
All surfaces must be 14°F or above and free from ice or water. Concrete to be treated must be at least four weeks old, completely dry and free of contaminants. Grease or oil should be removed with Watco Bio-D (or a similar emulsifying degreasant) and the area thoroughly washed off and allowed to dry. Very smooth concrete or concrete with surface laitance (a weak dusty layer) should be abraded or etched with Watco Cemtetch to ensure adequate adhesion. The concrete should be thoroughly washed down and allowed to dry after treatment with Watco Cemtetch. Previously painted surfaces should be thoroughly abraded by sanding to improve adhesion and to remove any weak or loose material. A trial area is advisable to test compatibility with previous coatings. Below 40°F it may be necessary to avoid processes which involve wetting the floor due to the difficulty in drying. A good sweep or mechanical brushing may be sufficient. Do not apply outside if rainfall is imminent.

Mixing
Mix between 15°F and 75°F. Remove the two inner tins from the tall outer tin. Stir each tin thoroughly and pour all of the contents into the outer tin (scrape around the inside of the tins to remove any residue). Mix the components together thoroughly using a spatula or a similar wide bladed tool (a piece of wooden batten is ideal). Continue mixing until an even color and consistency are obtained. Do not mix more than one pack at a time. If a paint stirrer fitted to an electric drill is used, also use the spatula to blend in any unmixed material from the sides and bottom of the tin. Do not dilute. Pot life is 25-30 minutes at 60°F

Application
If appearance is critical we recommend the application of a small trial area first.

Apply between 15°F and 85°F. The viscosity will be somewhat thicker at very low temperatures, reducing coverage a little.

Data Sheet

Watco Toughline incorporates the latest polyaspartic resin technology for a high quality, highly wear resistant line marking paint that can be applied as low as 15°F. This makes it the perfect line marker for unheated warehouses, walk in fridges, cold stores and loading bays. It is particularly useful for exterior applications as it resists chalking, fading, weathering and UV discoloration.

  • Flexible
  • UV resistant
  • Can be applied between 15°F and 85°F
  • Takes heavy wear and tear
  • Excellent chemical resistance


Coverage: Approximately 75m of a 50mm wide line per 1 liter, allowing for one coat.

Curing times are dependent on site conditions, but the following can be used as a guide:

 

Curing Times
  70°F 40°F 32°F 14°F
   Recoatable       4-5 hrs       10-12 hrs       16 hrs       30 hrs   
   Light Traffic       6-8 hrs       18 hrs       24 hrs       36 hrs   
   Heavy Traffic       12 hrs       24 hrs       36 hrs       48 hrs   

Warning: Cancer and Reproductive harm image

Usage Interior/Exterior: Interior or Exterior
Suitable for: Concrete, asphalt, wood and metal
Coverage: 240 linear feet at 2" wide
Recommended Number of Coats: 1
Pot Life: 25-30 minutes at 60°F
Curing Time (Hours): 6 Hours at 70°F

Surface Preparation
All surfaces must be 14°F or above and free from ice or water. Concrete to be treated must be at least four weeks old, completely dry and free of contaminants. Grease or oil should be removed with Watco Bio-D (or a similar emulsifying degreasant) and the area thoroughly washed off and allowed to dry. Very smooth concrete or concrete with surface laitance (a weak dusty layer) should be abraded or etched with Watco Cemtetch to ensure adequate adhesion. The concrete should be thoroughly washed down and allowed to dry after treatment with Watco Cemtetch. Previously painted surfaces should be thoroughly abraded by sanding to improve adhesion and to remove any weak or loose material. A trial area is advisable to test compatibility with previous coatings. Below 40°F it may be necessary to avoid processes which involve wetting the floor due to the difficulty in drying. A good sweep or mechanical brushing may be sufficient. Do not apply outside if rainfall is imminent.

Mixing
Mix between 15°F and 75°F. Remove the two inner tins from the tall outer tin. Stir each tin thoroughly and pour all of the contents into the outer tin (scrape around the inside of the tins to remove any residue). Mix the components together thoroughly using a spatula or a similar wide bladed tool (a piece of wooden batten is ideal). Continue mixing until an even color and consistency are obtained. Do not mix more than one pack at a time. If a paint stirrer fitted to an electric drill is used, also use the spatula to blend in any unmixed material from the sides and bottom of the tin. Do not dilute. Pot life is 25-30 minutes at 60°F

Application
If appearance is critical we recommend the application of a small trial area first.

Apply between 15°F and 85°F. The viscosity will be somewhat thicker at very low temperatures, reducing coverage a little.

Videos Hide Videos Show Videos