Basket (0)

Watco manufactures industrial strength floor paints, repair materials and non slip products


Try our new site

Concrex® Tinted Epoxy Repair Mortars

Concrex® Tinted Epoxy Repair Mortars

$129.29 From

Repair concrete with our incredibly tough, concrete epoxy repair mortar for cracked, spalled, eroded or damaged floors, bay edges and broken steps. Available in 20 or 50 lb. packs.

Black Navy Gray Silver Gray Tile Red
Add Items to Cart

* Required Fields


There are no price breaks available.

$129.29 From
Product Details
Completing a concrete hole repair project? Concrex® is the right choice! Concrex® now contains epoxy novolac resin for an even tougher epoxy resin mortar ideal for repairing cracked, spalled, eroded, damaged or peeling concrete floors including bay edges, broken steps and concrete bleachers. Concrex also works great as a concrete hole filler.

Features and Benefits of Concrex® – Concrete Epoxy Resin Mortar:

  • Cures to a granite hard finish
  • 10 Year Warranty
  • Epoxy novolac resin mortar
  • Can be feather-edged up to 2” depth
  • Chemical & chip resistant with anti slip properties
  • Impermeable & non-dusting
  • Will not shrink or expand during cure
  • Ready for light traffic in 3-6 hours
  • Covers approximately @ a 1/4" thick 9 sq. ft. per 20 lb. kit and 23 sq. ft. per 50 lb. kit
  • Can be used for both interior & exterior applications
  • Tools: Tack Coat Primer (required for screeding), Finishing Trowel, and Mix & Apply Margin Trowel

    Concrex is far stronger than Concrete.
    Comparison over 28 days
    Tensile Strength  Concrex 2234 psi     Concrete 493 psi  
    Flexural Strength  Concrex 8108 psi    Concrete 1001 psi  
    Compressive Strength   Concrex 8006 psi    Concrete 4322 psi  

    Application Video

    Prop 65

    Concrex Advanced

    Quick Links

    Safety Data Sheet_20 lb. Black_A070209
    Safety Data Sheet_50 lb. Black_A070212
    Safety Data Sheet_20 lb. Silver Gray_A070507
    Safety Data Sheet_50 lb. Silver Gray_A070510
    Safety Data Sheet_20 lb. Tile Red_A070808
    Safety Data Sheet_50 lb. Tile Red_A070811
    Safety Data Sheet_20 lb. Navy Gray_A100015
    Safety Data Sheet_50 lb. Navy Gray_A100016
    Technical Data Sheet
  • Specifications
    Delivery Time (Days) Standard
    Primer Required Tack Coat (screeding primer)
    Usage - Interior / Exterior interior & exterior
    Usage - Suitable for concrete & metal
    Usage - Properties incredibly tough granite hard finish, chemical resistant, can be feather-edge to 2” depth (full strength is achieved at ¼”)
    Usage - Surfaces eroded or damaged concrete, bay edges, broken steps, sidewalks
    Coverage (sqft per kit) approximately 9 sq. ft. per 20 lb. kit at 1/4" thick or 23 sq. ft. per 50 lb. kit at 1/4" thick
    Application - Curing Time (hours) Light traffic 3-6 hr; Heavy traffic, 8-12 hr @ 60-70°F
    Application - Pot Life (hours) 1/2 to 1
    Min Application Temperature (deg F) 50
    How To Apply
    Surface Preparation: Surfaces should be clean, dry and free of all loose material. Wire brushing or sweeping is generally sufficient. If needed, wash with Bio-D® or a suitable degreaser or detergent solution, to remove grease and oil. Rinse and allow to dry.

    Priming: Tack Coat adhesive primer is recommended when applying Concrex® as a thin section screed or when applying to smooth, non-porous or metal surfaces.

    Mixing: Concrex® should be stored at an ambient temperature above 50°F for approximately 8 hours prior to use. Do not use material if air and surface temperatures are below 50°F. Each pack of Concrex contains aggregate pre-blended with resin and the curing agent. Do not mix inside the plastic bucket. Wearing protective gloves, tip the aggregate on to a mixing tray or board. Shake the containers of curing agent thoroughly until the liquid is a uniform color. Form the aggregate into a mound and leave a small hole in the middle. Empty the curing agent into the hole, ensuring the container is completely drained. Carefully mix the aggregate with the curing agent using a trowel until a smooth mortar is obtained. This will take several minutes. The more thorough the mixing, the ‘wetter’, smoother and more manageable the mix becomes. Alternatively, you can knead the mixture by hand, but you must wear suitable gloves. It is important to mix thoroughly until you achieve a consistent color.

    How to Mix Concrex

    Application: Place mixed material into the area to be repaired and spread out and finish with a steel trowel. To reduce ‘drag’ on the trowel, wet the blade with Mineral Spirits. This will aid in getting a smooth finish to the Concrex®. Concrex is normally applied in thicknesses of ¼-2 inches, but repairs can be feather-edged for a neat finish, as long as the majority of the repair is at least a ¼ inch thick. For repairs deeper than 2 inches, apply in separate layers (allow 6-8 hours between layers for curing) or use Concrex® Deep Fill (which can be applied 1/2-4 inches thick in one layer). There is no need to reapply Tack Coat if building up in layers.
    Request a Quote/Sample

    Home Delivery

    Shipping cost

    Over $1,250.00 FREE
    From $750.00 to $1,249.99 $52.00
    From $400.00 to $745.99 $40.50
    From $200.00 to $399.99 $33.50
    Up to $199.99 $19.50

    You might also need...

    © 2017 Watco Industrial Flooring. All Rights Reserved.

    Terms & conditions |  Privacy policy |  Site map |  About us


    Problem Solving