Basket (0)

Watco manufactures industrial strength floor paints, repair materials and non slip products

 

Try our new site

Concrex® Cold Set

Concrex® Cold Set

From

Cold curing version of our Concrex® concrete epoxy repair mortar, for low temperature exterior winter use and cold room conditions.

Silver Gray Tile Red
Add Items to Cart

* Required Fields

VIEW PRICE BREAKS

There are no price breaks available.

From
 
Product Details
Concrex® Cold Set is used as a cold curing concrete patch repair. It is excellent for low temperature applications such as cold room repairs, entrance way and door way repairs, or just repairing in winter conditions.

Features and Benefits of Concrex® Cold Set – Concrete Epoxy Resin Mortar:


  • Very hard-wearing & chemical-resistant
  • Provides a smooth impermeable surface
  • Can be used for repairs with a feather-edge
  • Ideal for eroded cold room floors, repairing entrance ways or doorways
  • Ready for traffic in 10 hours at 50°F or 48 hours at 32°F
  • Covers approximately 9 sq. ft. per 20 lb. kit at 1/4" thick
  • Suitable for concrete & metal
  • For use on interior & exterior substrates
  • Cures to a granite hard finish
  • Virtually indestructible concrete epoxy repair
  • Tools: Tack Coat Primer (required for screeding), Finishing Trowel, and Mix & Apply Margin Trowel

    Concrex is far stronger than Concrete.
    Comparison over 28 days
    Tensile Strength  Concrex 2234 psi     Concrete 493 psi  
    Flexural Strength  Concrex 8108 psi    Concrete 1001 psi  
    Compressive Strength   Concrex 8006 psi    Concrete 4322 psi  

    Prop 65


    Concrex Cold Set

    Quick Links

    Safety Data Sheet_Concrex Cold Set_Navy Gray_A120019
    Technical Data Sheet
  • Specifications
    Appearance flat finish
    Delivery Time (Days) standard
    Primer Required Tack Coat (screeding primer)
    Depth (in.) from feather-edge to 2
    Usage - Interior / Exterior interior & exterior
    Usage - Suitable for concrete & metal
    Usage - Properties suitable for exterior winter use and cold room conditions, hard-wearing and resistant to chemicals, impervious finish, can be used for repairs with a feather edge
    Usage - Surfaces floors, ramps, steps
    Coverage (sqft per kit) 9 per 20 lb kit at ¼” thick
    Application - Curing Time (hours) 10 hours at 50°F or above, 48 hours at 32°F
    Application - Pot Life (hours) 30 min. to 1 hour
    Application - Recommended Coats for repairs deeper than 2", apply in separate layers (allow 6-8 hours between layers for curing)
    Application - Application Condition clean, dry and free of all loose material
    Min Application Temperature (deg F) 32
    How To Apply
    Surface Preparation: Surfaces should be clean, dry and free of all loose material. Wire brushing or sweeping is generally sufficient. If needed, wash with Bio-D®, or suitable degreaser or detergent solution, to remove grease and oil, rinse and allow to dry.

    Priming: A primer is not usually required if patch or crack repairing.

    Mixing: Concrex Cold Set® should be stored at an ambient temperature above 50°F for approximately 8 hours prior to use. Do not use material if air and surface temperatures are below 32°F. Each pack of Concrex Cold Set contains aggregate pre-blended with resin and the curing agent. Do not mix inside the plastic bucket. Wearing protective gloves, tip the aggregate on to a mixing tray or board. Shake the containers of curing agent thoroughly until the liquid is a uniform color. Form the aggregate into a mound and leave a small hole in the middle. Empty the curing agent into the hole, ensuring the container is completely drained. Carefully mix the aggregate with the curing agent using a trowel until a smooth mortar is obtained, this will take several minutes. The more thorough the mixing, the ‘wetter’, smoother and more manageable the mix becomes. Alternatively, you can knead the mixture by hand, but you must wear suitable gloves. It is important to mix thoroughly until you achieve a consistent color.

    Application: Place mixed material into the area to be repaired and spread out and finish with a steel trowel. To reduce ‘drag’ on the trowel, wet the blade with mineral spirits. This will aid getting a smooth finish to the Concrex Cold Set®. Concrex Cold Set is normally applied in thicknesses of ¼ to 2”, but repairs can be feather-edged for a neat finish, as long as the majority of the repair is at least a ¼” thick. For repairs deeper than 2”, apply in separate layers (allow 6-8 hours between layers for curing) or use Concrex® Deep Fill (which can be applied ½ to 4” thick in one layer).
    Reviews
    Request a Quote/Sample
    Delivery

    Home Delivery

    Shipping cost

    Over $1,250.00 FREE
    From $750.00 to $1,249.99 $52.00
    From $400.00 to $745.99 $40.50
    From $200.00 to $399.99 $33.50
    Up to $199.99 $19.50

    You might also need...

    © 2017 Watco Industrial Flooring. All Rights Reserved.



    Terms & conditions |  Privacy policy |  Site map |  About us

            


    Problem Solving