Basket (0)

Watco manufactures industrial strength floor paints, repair materials and non slip products


Try our new site

Anti Slip Clear Coat Plus Floor Coating

Anti Slip Clear Coat Plus Floor Coating

Regular Price: $163.30

Special Price: $158.55  excl. tax

An exceptionally hard wearing two-component anti slip polyaspartic floor coating, with a mid-gloss clear finish for interior and exterior applications.

Add Items to Cart
  • Buy 1 for $163.30  excl. tax each

Regular Price: $163.30

Special Price: $158.55  excl. tax

Product Details
Anti Slip Clear Coat Plus is an exceptionally hard wearing two-component clear coating for protecting bare concrete or refreshing previously coated concrete floors. It cures to a mid-gloss finish to enhance the look of your premises. Use in a multitude of areas ranging from warehouses and showrooms to walk-in fridges and exterior car parking areas. Externally it will resist chalking, fading, feathering and has exceptional resistance to UV.

Features and Benefits of Anti Slip Clear Coat Plus – Protective Industrial Floor Coating:

  • Protects colored and decorative coatings from heavy wear and tear
  • Finely textured slip resistant finish
  • Low odor, low VOC
  • Can be used as a concrete floor sealer or clear coating
  • Easy roll-on application
  • Can be applied from 15 to 85°F
  • Excellent chemical resistance and durability
  • Suitable for internal and external use
  • Bare concrete: approximately 180 sq. ft. per Liter
  • Coated surface: approximately 300 sq. ft. per Liter
  • Cures in 6 to 8 hours for light foot traffic
  • Tools: 18” Roller, or 4” Paint Brush and Xylene for tool cleanup

  • VOC < 100g/L Industrial manitenance coating suitable for exposure to chemical mixtures and solutions as well as repeated industrial cleaning.

    Prop 65

    Concrex Advanced

    Quick Links

    Safety Data Sheet_Clear Coat Plus Anti Slip_B691945
    Technical Data Sheet
    Appearance clear, gloss finish
    Delivery Time (Days) Standard
    Primer Required no
    Usage - Interior / Exterior interior & exterior
    Usage - Suitable for bare & previously coated concrete
    Usage - Properties easy to apply, two component finely textured clear coat, protects bare concrete, refreshes previously coated floors, durable, chemical resistant, virtually odorless
    Usage - Surfaces floors. VOC < 100g/L Industrial manitenance coating suitable for exposure to chemical mixtures and solutions as well as repeated industrial cleaning.
    Coverage (sqft per kit) bare concrete: approximately 180sq. ft./L.; coated surface: approximately 300 sq. ft./L
    Application - Curing Time (hours) light foot traffic: 6-8 hr.; normal service: 24-48 hr.; vehicle traffic: 72-96 hr.; re-coat: 4-5 hr., not exceeding 48 hr.
    Application - Pot Life (hours) 25 to 30 min. @ 70º F
    Application - Recommended Coats one coat will cover most surfaces
    Max Application Temperature (deg F) 85
    Application - Application Condition clean & dry
    Min Application Temperature (deg F) 15
    How To Apply
    SURFACE PREPARATION: The concrete surface must be clean, dry and free of loose material. New concrete should be allowed to cure for 28 days prior to coating. Remove oil, dirt, grease and other chemical contaminants by cleaning with detergent or other suitable cleaner. Rinse thoroughly. Use Cemtetch® to remove unsound laitance and create a proper surface profile to the concrete. Rinse thoroughly and allow to dry before application of the Anti-Slip Clear Coat Plus. Note: Concrete floors on grade must be free of moisture transmission from the ground. If there is any doubt about the dryness of the concrete, conduct a test by simply taping a piece of 4 mil plastic sheet 18” by 18” on the bare concrete for 24 hours. Be sure to tape all four sides. After 24 hours, check the concrete for signs of moisture. The concrete will be darker if damp. If moisture is found, allow additional drying time (10-14 days) and repeat test. Persistent moisture transmission will prevent proper performance of the coating, please contact a Watco Industrial Flooring Expert at (855) 627-6350 for assistance. Also, check for curing compound or other types of sealers by pouring a small amount of water onto the concrete. If water soaks in, the surface is suitable for coating. If water beads up on the concrete, the surface is not porous and a test application is warranted to ensure proper adhesion will develop. Sanding or mechanical abrading may be required if proper adhesion does not develop. Previously coated floors need to be in good sound condition with proper adhesion to the concrete substrate. Check the adhesion of the previous coating by cutting a small X in the coating using a sharp razor knife, firmly apply a piece of 2” duct tape over the center of the X cut, then pull off with a fast snap. The coating is suitable to topcoat if no significant previous coating is removed beyond the X cut. If the coating fails this test, then additional surface preparation is required. It is recommended previously coated floors be sanded and vacuumed prior to application of the Anti-Slip Clear Coat Plus.
    MIXING: Mix material when air temperature is between 50-77ºF (10-25ºC) Combine the base and activator by power mixing. Mix at 500-750 rpm for 1-3 minutes. Do not over mix or use higher speeds. This can introduce air into the coating causing small bubbles in the finish. It is very important to transfer as much activator as possible, scrape the sides and bottom of the container thoroughly. Mix the two components together for 1-3 minutes being careful to not pull air into the mixture. Add the anti-slip aggregate and mix for another 30 seconds. Once mixed, do not delay coating application as the pot life is only 25-30 minutes at 70ºF. NOTE: Do not scrape the sides or bottom of the mixed container. Use only the material that flows naturally out of the container. Doing so may result with un-activated material from the side wall of the container being applied. This will cause soft spots in the coating.
    APPLICATION: Be sure the floor is clean, dry, and dust free. If needed, vacuum to remove dust and debris. Apply only when air, material and floor temperatures are between 15-85°F (-10.5-29°C). Use a good quality phenolic core roller with a 3/8” lint-free nap. Do not excessively over roll and make all final passes in the same direction. For best results, maintain a wet edge and end application at natural breaks in the floor like control joints or expansion joints. Do not apply in excess, avoid a heavy wet film. Use in well ventilated areas.
    CLEAN UP: Clean up equipment with Xylene.
    Request a Quote/Sample

    Home Delivery

    Shipping cost

    Over $1,250.00 FREE
    From $750.00 to $1,249.99 $52.00
    From $400.00 to $745.99 $40.50
    From $200.00 to $399.99 $33.50
    Up to $199.99 $19.50

    You might also need...

    © 2017 Watco Industrial Flooring. All Rights Reserved.

    Terms & conditions |  Privacy policy |  Site map |  About us


    Problem Solving