- Product Details
Safety Coat is a uniquely formulated, slip resistant, industrial epoxy floor coating which uses a special aggregate suspended in the liquid, allowing the coating to dry to an evenly textured, slip-resistant surface. This non slip floor treatment provides a more attractive and easier to clean finish than conventional “gritty” paint. It is suitable as an interior coating for concrete or wood and can be used on all potentially slippery floors in heavy wear areas. Available in Silver Gray, Mid Gray, Tile Red, Blue, and Green.
Features and Benefits of Safety Coat - Anti-slip Floor Coating:
- This non slip epoxy floor coating contains fine, slip resistant particles embedded in a tough epoxy resin coating
- Easy to clean with a dry dust mop or wet floor mop
- Great for floors, stairs, platforms & ramps
- Extremely durable & chemical resistant
- Hard wearing
- Can withstand forklift traffic
- Easily applied by Roller, and Paint Brush to cut in the walls
- 2 coats in one day
- Non-flammable, virtually solvent free & odorless formula
- Gives a professional looking finish
- Ready for traffic in 12 hours
- Covers approximately 240 sq. ft. per kit
- Can withstand forklift traffic
- Also available in clear coat, fast curing Safety Coat Rapid , and extra coarse Safety Coat Plus
Quick LinksSafety Data Sheet_Safety Coat_Navy Gray_C240401
Safety Data Sheet_Safety Coat_Silver Gray_C240502
Safety Data Sheet_Safety Coat_Tile Red_C240805
Safety Data Sheet_Safety Coat_Blue_C240903
Safety Data Sheet_Safety Coat_Green_C241104
Technical Data Sheet
- Specifications + Technical Data Sheets
Appearance fine aggregate textured, low sheen finish Delivery Time (Days) Ships in 24 hours, delivers in 1-3 days Nationwide Primer Required no Usage - Interior / Exterior Interior Usage - Suitable for repair, new use Usage - Properties fine traction-enhancing particles, anti slip epoxy resin floor coating, easily applied, extremely durable, chemical resistant, non-flammable, solvent free, virtually odorless Usage - Surfaces concrete and wood floor surfaces Coverage (sqft per kit) 240 per 1 gal. kit Application - Curing Time (hours) approximately 12 hours @ 60-70°F for light foot traffic Application - Pot Life (hours) 2 hours at 60-70°F Application - Recommended Coats 2 Max Application Temperature (deg F) 90 Application - Application Condition dry Min Application Temperature (deg F) 60
- How To Apply
Surface Preparation: The concrete surface must be clean, dry and free of loose material. New concrete should be allowed to cure for 28 days prior to coating. Remove oil, dirt, grease and other chemical contaminants by cleaning with detergent or other suitable cleaner. Rinse thoroughly. Use Cemtetch® to remove unsound laitance and create a proper surface profile to the concrete. Rinse thoroughly and allow to dry before application of the Safety Coat. Previously coated floors need to be in good sound condition with proper adhesion to the concrete substrate. Glossy finishes should be sanded to provide a surface profile. Wooden surfaces should also be sanded. Two or three coats may be required on open textured surfaces such as chipboard. Not recommended for use onto metal or latex leveling compounds.
Mixing: Combine the base and activator components into a clean 2 gallon or 5 gallon plastic or metal pail. Use a paint paddle or spatula to scrape out and transfer as much of the material as possible. Mix the components thoroughly until an even, uniform color is achieved. If using a power mixer use a paint paddle or spatula to blend in any unmixed material from the sides and bottom of the pail. Do not mix more than one unit at a time. Immediately pour the material into a roller pan and do not delay application. The pot life is approximately two hours at 60-70°F. Higher temperatures will reduce the pot life.
Application: Apply in a well ventilated area when the air and surface temperatures are between 60-90°F. The air and surface temperature must be at least 60°F prior to application. Use a good quality lint free 3/8" nap roller with a phenolic core. The first coat of Safety Coat will act as a priming/sealing coat on most surfaces. The second coat should be applied as soon as the first coat is dry (approximately 12 hours at 60-70°F). Do not exceed the maximum coverage of 240 sq ft per kit. Occasional stirring of the product will ensure a more even distribution of the aggregate. In exceptional temperature conditions, please contact a Watco Industrial Flooring Expert at (855) 627-6350.
- Case Studies
- Request a Quote/Sample