- Product details
High Build Epoxy is a two part, durable 100% solids protective epoxy resin floor coating for concrete. It provides a high gloss, easy to clean surface and is resistant to very heavy wear, oils and solvents.
With High Build Epoxy, only one coat is usually required, except on very porous surfaces which should be treated first with 4-Hour Epoxy Primer. High Build Epoxy is ideal for areas such as: showrooms, warehouses, heavy traffic areas where chemicals may be spilled, production areas and any area where increased durability and high quality finish are important.
Features and Benefits of High Build Epoxy - Interior Epoxy Resin Floor Coating:
- Our highest gloss, toughest epoxy resin coating
- Excellent chemical resistance
- Roller applied, two component 100% solids epoxy resin
- Low solvents & virtually odorless during application
- High build formula, up to 8 mils thick in one coat
- Suitable for interior applications on concrete, wood or metal
- Resistant to oil, solvents and harsh cleaning chemicals
- Covers approximately 160 sq. ft. per 1 gallon kit. One coat covers most surfaces
- Ready for light traffic after 12 to 16 hours
Use with 4-Hour Epoxy Primer on very porous surfaces or Powerfloat Primer on smooth, hard surfaces or power floated floors
Quick LinksSafety Data Sheet_High Build Epoxy_Navy Gray_B190416
Safety Data Sheet_High Build Epoxy_Blue_B190418
Safety Data Sheet_High Build Epoxy_Silver Gray_B190517
Safety Data Sheet_High Build Epoxy_Tile Red_B190820
Safety Data Sheet_High Build Epoxy_Green_B191119
Technical Data Sheet
Appearance gloss Delivery Time (Days) Standard Primer Required yes, on very porous surfaces Usage - Interior / Exterior interior Usage - Suitable for repair, new use Usage - Properties highest performance roller applied floor coating, glossy, hygienic and easy to clean surface, resistant to very heavy wear and a wide range of chemicals, low solvent formula, virtually odorless Usage - Surfaces floors Coverage (sqft per kit) approximately 160 sq. ft. per 1 gallon kit Application - Curing Time (hours) light traffic after 12-16 hours at 60-70°F Application - Pot Life (hours) approximately 1 hour at 60°F Application - Recommended Coats one coat covers most surfaces Max Application Temperature (deg F) 90 Application - Application Condition dry warm conditions Min Application Temperature (deg F) 60
- Preparation & Application
Surface Preparation: The concrete surface must be clean, dry and free of loose material. New concrete should be allowed to cure for 28 days prior to coating. Remove oil, dirt, grease and other chemical contaminants by cleaning with detergent or other suitable cleaner. Rinse thoroughly. Use Cemtetch® to remove unsound laitance and create a proper surface profile to the concrete. Rinse thoroughly and allow to dry. NOTE: Concrete that has a sealer or curing agent on it may not respond to the Cemtetch treatment. It may be necessary to remove the sealer and create a surface profile by a mechanical method.
Primer: Use 4-Hour Epoxy Primer on very porous surfaces or Powerfloat Primer on hard, smooth surfaces or powerfloated floors.
Mixing: Store materials at 60°F for 8 hours prior to use. Combine the base and activator components. Use a paint paddle or spatula to scrape out and transfer as much of the material as possible. Mix the components thoroughly until an even, uniform color is achieved. If using a power mixer use a paint paddle or spatula to blend in any unmixed material from the sides and bottom of the pail. Do not mix more than one unit at a time. Immediately pour the material into a roller pan and do not delay application. The mixed components should be used immediately. The product has a pot life of one hour maximum at 60°F. Higher ambient temperatures will reduce the pot life. To extend pot life in higher temperatures the mixed components should be emptied into a shallow tray.
Application: Best results are obtained in warm conditions, (minimum 60°F). On horizontal surfaces apply by 3/8" nap roller in one coat. On vertical surfaces two thin coats are recommended. The second coat should be applied within 24 hours.
Curing Time: The product will cure overnight (12-16 hours) at 60°F to accept light traffic the next day; full chemical and wear resistance is achieved over 7 days (at a minimum constant temperature of 60°F). Temperatures of 50°F will slow down or arrest the curing of the product. Water should not be allowed to lie on the surface for at least 7 days. Avoid washing the surface for 7 days after coating.
Coverage: A gallon kit will cover approximately 160 sq. ft. when applied by roller. Brush application may result in reduced coverage.
You might also need...
$153.80 excl. tax
$85.00 excl. tax As low as: $72.25 excl. tax
$110.00 excl. tax As low as: $93.50 excl. tax
$175.00 excl. tax As low as: $157.00 excl. tax
$170.00 excl. tax
Watco Industrial Flooring, 11 Hawthorn Parkway, Vernon Hills, Illinois, 60061