Basket (0)

Watco manufactures industrial strength floor paints, repair materials and non slip products

Concrex High Temperature

Concrex High Temperature

$166.90  excl. tax

Tolerates environments exposed to high heat and steam cleaning. Same great qualities as normal Concrex except resists temperatures up to 212°F.

Add Items to Cart
VIEW PRICE BREAKS
  • Buy 1 for $166.90  excl. tax each
  • Buy 2 for $158.56  excl. tax each and save 5 %
  • Buy 3 for $150.21  excl. tax each and save 10 %
 
Product Details
Epoxy repair mortar that can repair damage caused by hot equipment like ovens and fryers when normal concrete fails. Can stand up to heat in front of furnaces, ovens and other hot elements.

Features and Benefits of Concrex® - Concrete Repair Patch:


  • Our strongest epoxy resin mortar ever!
  • Virtually indestructible
  • Can be feather-edged
  • Chemical-resistant and anti-slip
  • Impermeable & non-dusting
  • Will not shrink or expand during cure
  • Ready for light traffic in 3-6 hours.
  • Covers approximately 12 sq. ft. per 20 lb. kit at 1/4" thick



    Quick Links

    Safety Data Sheet
    Technical Data Sheet

    Application Video


  • Specifications
    Delivery Time (Days) Ships in 24 hours, delivers in 1-3 days
    Coverage (sqft per kit) approximately 10 sq. ft. per 22 lb. kit at 1/4" thick
    Application - Curing Time (hours) 5-6
    Application - Pot Life (hours) 30 Minutes to 1 Hour
    Min Application Temperature (deg F) 50
    How To Apply
    Surfaces should be clean, dry and free of all loose material. Wire brushing or sweeping is generally sufficient. If needed, wash with Bio-D or a suitable degreaser or detergent solution, to remove grease and oil, rinse and allow to dry.

    Mixing

    Concrex® should be stored at an ambient temperature above 50°F for approximately 8 hours prior to use. Do not use material if air and surface temperatures are below 50°F, apart from Concrex Cold Set which can be applied at 15°F. Each pack of Concrex contains aggregate pre-blended with resin and the curing agent. Do not mix inside the plastic bucket. Wearing protective gloves, tip the aggregate on to a mixing tray or board. Shake the containers of curing agent thoroughly until the liquid is a uniform color. Form the aggregate into a mound and leave a small hole in the middle. Empty the curing agent into the hole, ensuring the container is completely drained. Carefully mix the aggregate with the curing agent using a trowel until a smooth mortar is obtained, this will take several minutes. The more thorough the mixing, the ‘wetter’, smoother and more manageable the mix becomes. Alternatively, you can knead the mixture by hand, but you must wear suitable gloves. It is important to mix thoroughly until you achieve a consistent color.


    Application

    Place mixed material into the area to be repaired and spread out and finish with a steel trowel. To reduce ‘drag’ on the trowel, wet the blade with mineral spirits. This will aid getting a smooth finish to the Concrex. Concrex is normally applied in thicknesses of ¼-2 inches, but repairs can be feather-edged for a neat finish, as long as the majority of the repair is at least a ¼ inch thick. For repairs deeper than 2 inches, apply in separate layers (allow 6-8 hours between layers for curing) or use Concrex Deep Fill (which can be applied ½-4 inches thick in one layer). There is no need to reapply Tack Coat if building up in layers.

    Reviews
    Request a Quote/Sample
    Delivery

    Home Delivery

    Shipping cost

    Over $1,250.00 FREE
    From $750.00 to $1,249.99 $49.00
    From $400.00 to $749.99 $39.00
    From $100.00 to $399.99 $32.00
    Up to $99.99 $19.50

    © 2017 Watco Industrial Flooring. All Rights Reserved.



    Terms & conditions |  Privacy policy |  Site map |  About us